Ultem 9085 3D Printing in Pasadena CA

Get Accurate Models With Ultem 9085 3D Printing in Pasadena CA!

Due to the extensive capabilities of ProTek Models and ProTek 3D, there are very few limitations on how far we can take your 3D printing project. We work with a variety of materials, including Ultem 9085, so you can find the perfect material for your project. When it comes to Ultem 9085 3D Printing in Pasadena CA, ProTek Models is the best option in town!

Ultem 9085 3D Printing Specs

If you need a material that is approved for aircraft interiors or simply need something that has a high strength-to-weight ratio, Ultem 9085 is a good choice that provides the following specs:

Mechanical Properties

  •  Tensile Strength, Yield (Type 1, 0.125”, 0.2”/min): 6,800 – 4,800 psi
  • Tensile Strength, Ultimate (Type 1, 0.125”, 0.2”/min): 9,950 – 6,100 psi
  • Tensile Modulus (Type 1, 0.125”, 0.2”/min): 312,000 – 329,000
  • Tensile Elongation at Break (Type 1, 0.125”, 0.2”/min): 5.8% – 2.2%
  • Tensile Elongation at Yield (Type 1, 0.125”, 0.2”/min): 2.2% – 1.7%
  • Flexural Strength (Method 1, 0.05”/min): 16,200 – 9,900 psi
  • Flexural Modulus (Method 1, 0.05”/min): 331,000 – 297,000 psi
  • Flexural Strain at Break (Method 1, 0.05”/min): 3.7%
  • IZOD Impact, notched (Method A, 23 °C): 2.2 ft – lb/in to 0.9 ft-lb/in
  • IZOD Impact, un-notched (Method A, 23 °C): 14.6 ft – lb/in – 3.2 ft – lb/in
  • Compressive Strength, Yield (Method 1, 0.05”/min): 14,500 – 12,700 psi
  • Compressive Strength, Ultimate (Method 1, 0.05”/min): 26,200 – 13,100 psi
  • Compressive Modulus (Method 1, 0.05”/min): 1,030,000 – 251,000 psi

Thermal Properties

  • Heat Deflection (HDT) @ 264 psi, 0.125” unannealed: 307 °F
  • Glass Transition Temperature (Tg): 367 °F
  • Coefficient of Thermal Expansion: 3.67×10-05 in/(in·°F)

Electrical Properties

  • Volume Resistivity: 4.9 x1015 – 8.2×1015 ohm-cm
  • Dielectric Constant: 3 – 3.2
  • Dissipation Factor: .0026 – .0027
  • Dielectric Strength: 110 – 290 V/mil

 

To see if Ultem 9085 3D Printing in Pasadena CA is right for your project, give ProTek Models a call today!

Contact ProTek Models for Reliable Ultem 9085 3D Printing in Pasadena CA!

With over 15 years of experience in FDM 3D printing, you can trust ProTek Models to get the job done in a timely and affordable manner. We handle everything in-house, so you can count on us to deliver quality parts and assemblies that meet your tolerances. Contact us today to learn more about Ultem 9085 3D Printing in Pasadena CA.

Contact Us

If you are looking for a custom scale model or more specifically, Ultem 9085 3D printing in Pasadena CA Contact us today..

Phone: (909) 477-6866
Fax: (909) 477-6867
Email: info@protekmodels.com
Address:  9155 Archibald Ave., Suite 909, Rancho Cucamonga, CA 91730