Ultem 9085 3D Printing in Santa Ana CA

Get Accurate Models With Ultem 9085 3D Printing in Santa Ana CA!

Combined with a Fortus 3D Printer, Ultem 9085 resin allows ProTek Models to produce fully functional parts that are ideal for advanced functional prototypes or end-use without the cost or lead time of traditional tooling. If you are looking to utilize Ultem 9085 in your FDM 3D printing project, trust ProTek Models to handle the job. We offer reliable and timely Ultem 9085 3D Printing in Santa Ana CA.

Ultem 9085 3D Printing Specs

Ultem 9085 not only has a strong FST (flame, smoke and toxicity) rating, but it also meets more stringent test criteria and retains material traceability required by the aerospace industry. In addition, Ultem 9085 also provides the following specs:

Mechanical Properties

  •  Tensile Strength, Yield (Type 1, 0.125”, 0.2”/min): 6,800 – 4,800 psi
  • Tensile Strength, Ultimate (Type 1, 0.125”, 0.2”/min): 9,950 – 6,100 psi
  • Tensile Modulus (Type 1, 0.125”, 0.2”/min): 312,000 – 329,000
  • Tensile Elongation at Break (Type 1, 0.125”, 0.2”/min): 5.8% – 2.2%
  • Tensile Elongation at Yield (Type 1, 0.125”, 0.2”/min): 2.2% – 1.7%
  • Flexural Strength (Method 1, 0.05”/min): 16,200 – 9,900 psi
  • Flexural Modulus (Method 1, 0.05”/min): 331,000 – 297,000 psi
  • Flexural Strain at Break (Method 1, 0.05”/min): 3.7%
  • IZOD Impact, notched (Method A, 23 °C): 2.2 ft – lb/in to 0.9 ft-lb/in
  • IZOD Impact, un-notched (Method A, 23 °C): 14.6 ft – lb/in – 3.2 ft – lb/in
  • Compressive Strength, Yield (Method 1, 0.05”/min): 14,500 – 12,700 psi
  • Compressive Strength, Ultimate (Method 1, 0.05”/min): 26,200 – 13,100 psi
  • Compressive Modulus (Method 1, 0.05”/min): 1,030,000 – 251,000 psi

Thermal Properties

  • Heat Deflection (HDT) @ 264 psi, 0.125” unannealed: 307 °F
  • Glass Transition Temperature (Tg): 367 °F
  • Coefficient of Thermal Expansion: 3.67×10-05 in/(in·°F)

Electrical Properties

  • Volume Resistivity: 4.9 x1015 – 8.2×1015 ohm-cm
  • Dielectric Constant: 3 – 3.2
  • Dissipation Factor: .0026 – .0027
  • Dielectric Strength: 110 – 290 V/mil

To learn more about Ultem 9085 3D printing in Santa Ana CA, contact the knowledgeable team at ProTek Models.

Contact ProTek Models for Reliable Ultem 9085 3D Printing in Santa Ana CA!

At ProTek Models, our experienced FDM 3D printing specialists handle everything in-house. That’s why you can trust us with your Ultem 9085 3D printing in Santa Ana CA, no matter how big or small the job is. Contact us today to learn more or request a quote for our FDM 3D printing services.

Contact Us

If you are looking for a custom scale model or more specifically, Ultem 9085 3D printing in Santa Ana CA Contact us today..

 

Phone: (909) 477-6866
Fax: (909) 477-6867
Email: info@protekmodels.com
Address:  9155 Archibald Ave., Suite 909, Rancho Cucamonga, CA 91730